A clogged sewer is a very serious problem that can be considered a plumbing emergency and a pronounced health issue.

A study by Massachusetts Department of Public Health Division of Community Sanitation (DPH), and the Massachusetts Department of Environmental Protection (MassDEP) shows that:

“Pathogens, which are disease-causing agents; which can be in the form of bacteria, viruses, mold spores, or protozoans, are normally present in large numbers in sewage wastes.”

When the sewer is clogged, there will be limited or no space for the wastewater. Hence, it will return to the water supply system in one way or another. If you are clogging a sewer, you should not use any of the pipes in the house until the shutdown is over.

If you suspect that a sewer is blocked, it is important to confirm this and take quick steps to fix it.

There are several indications that a sewer can be blocked:

1. Several fittings are blocked

A very obvious sign of blockages in a sewer is when more than one sanitary fitting is secured simultaneously.

This applies in particular to toilets, but other devices may also be involved. If you suspect that a sewer is blocked, start checking other fittings in the house.

2. Unusual reactions when using devices

Next, if you suspect blockages in the sewer system, look for unexpected or unusual reactions when using sanitary fittings.

i). Toilets: Toilets have the most direct way to the sewer and the largest drain in the house. So, if you have a problem with the sewer, you’ll notice it first here. It is rare that a main pipe collector stops and the toilets still functions properly.

ii). Tub and shower: Other drains typically affected by the main stop are those in the tub and shower. This is due to the fact that they are located at a lower level than the gutters. Check if the tub and shower channels are blocked if you suspect that a sewer is blocked.

iii). Flush the toilet: If flushing the toilet causes water backwater or gets into the tub or shower, this is usually a clear sign of a blockage drain in the sewer system.

The rinsed water, which cannot drain through the sewer, flows up the pipes and exits at the lowest point, which is normally the shower drain.

iv). Let the sink run: Another strange reaction is the trapped air in the water pipe. Do this by introducing water into the closest sink to the toilet for one minute.

If the toilet is bubbling or you see the water level in the toilet rising, then the blockage is very likely in the main sewer and not in the toilet.

v). Washing machine: Running the washing machine can cause an unexpected clogging of a sewer. If the water draining from the washing machine causes the toilet to overflow or fall back into the bathtub or shower, this could be an indication that the sewer is blocked.

Note: This symptom can only be a problem with the washing machine and shower and not a blockage of the sewer. If the toilets are still flushing well, this is probably due to a standstill of the washing machine and not to a sewage pipe.

3. Dewatering at clean-out

If you have a main line cleaning, you have an additional possibility to check a sewer blockage. Look for ‘cleaning’ if you don’t already know where it is. Open the cleaning by either unscrewing or pulling it to remove the cap.

Check the ‘cleaning’ for waste or water that may be deposited there. Normally, no water should enter the cleaning pipe.

If water comes up and out of the cleaning or is in the pipe, this confirms that the sewer is affected in some way.

Cleaning a sewer requires a sewer line. You can either call a professional installer or rent the machine and clean it yourself. In any case, a sewer should be blocked as soon as possible.

How to tell if your septic tank is clogged

Over time, the drain field can become blocked even without external damage to tree roots or crushing pressure due to an accumulation of soap, grease and solid waste in the gravel and soil around the drain field pipes.

These substances lead to secure the wastewater and caustic solution in the soil above. If your septic drain field is clogged, you will see several different symptoms.

This can also occur in damp winters when your septic drain field is clogged.

Check your lawn to see where the septic drain field is located. Investigation of the soil surface is critical at this point, look for soaked areas and bad smells in the drain field.

Study the grass to see if it looks greener over the drain area than the other areas of your lawn. You can also see a slimy black layer over the drain field area.

For persistent problems with wastewater, put fuses and toilets in the sewer system, even after you have had the septic tank pumped.

Tips and Warnings

By having your septic tank pumped and maintained, as well as reducing your water consumption drastically, sometimes, you can correct a clogged runoff field.

Often damaged with clogged or septic field pipe, however, the drain field system must be replaced by a specialist.

Do not wait to fix a clogged sewage drain later. The longer you wait to fix the drain area, the worse the damage will be.

This eliminates blockages from the drainage pipe

Clogged sewage pipes are uncomfortable, annoying and lead to a huge impairment of the quality of living.

However, the causes, as well as the possibilities for elimination, may differ from case to case.  

Clogged sewage pipes in the household can quickly become a problem because on the one hand, constipation spreads especially in the toilet sewage pipes — and soon enough, an unpleasant smell in the entire premises.

On the other hand, overflowing toilets, washing machines, and drains, can of course, cause water damage, which must be eliminated as quickly as possible and often involve costly renovations. If the sewage pipe is clogged, you should act quickly to avoid further problems.

How does a blockage develop in the sewage pipe?

The causes of a clogged sewage pipe can be manifold. Sometimes, there is a lack of a tree, but in many cases, it is a wrong and improper use of the drain.

If there is a lack of a tree in wastewater treatment, incorrect processing of the material or improper installation may be the cause.

When assembling the individual pipes, therefore, an experienced specialist in the sanitary sector should be consulted — because drain pipes should never be installed due to the complexity of the installation itself. So blockages can be effectively prevented during construction.

Our Tip:

In rare cases, it can also lead to a backlog, which entails overflowing drains: Flooding, the sewage from the sewer returns back into the living spaces and results in a damage.

Backflow stops and lifting equipment can be used by a professional to prevent this problem.

In addition to improper installation by laymen, the emergence of clogged sewage pipes can of course also be due to the fact that the inhabitants of the premises give solids into the drain.

Materials such as cat litter, leftovers and other waste such as kitchen paper cause constipation.

Even oils and fats such as butter, which are still liquid when hot, become solid when poured into the drain. Consumers should therefore absolutely refrain from giving unintended material into the drain.

In addition, massive calcifications or smaller deposits can settle and gradually lead to a narrowing of the pipe.

This bottleneck also leads to blockage of the sewer pipe in the long-term and is often noticeable at an early stage: if the runoff smells bad or makes a gurgling noise, a plant mechanic should be consulted to eliminate the constriction.

Blockage removal

Many people first try to repair the clogged sewer pipe themselves and eliminate the damage on their own. Putties, household cleaners and even makeshift tools such as sliced water bottles are often recommended.

In most cases, however, the problem is not resolved – mostly the obstruction is superficially and slightly eliminated.

For example, deposits can hardly be completely removed by these means, which in the long-term would lead to a bottleneck again — and sooner or later to a new blockage. In addition, a layman can never really judge where the cause of the problem lies.

If a sewage pipe is clogged, you should call a specialist as soon as possible. He can investigate the damage on site and determine the exact cause.

Often, the cause is within the piping system, which requires dismantling – in some cases, the sewer pipe must also be renewed.

Our Tip:

Wastewater pipes are also renewed if they are made of lead and therefore pose a risk to health. A renovation also takes place when the sewers are no longer tight.

Basically, the expert can use a chemical cleaner with which the blockage is solved.

Sometimes, the problem can also be solved by flushing, where a large amount of water is passed through the pipe at high speed to remove impurities and deposits.

Image Source: LuminaNews

For less severe blockages that are not accessible without tools, the expert uses a pipe cleaning spiral.

This is either mechanically or electrically passed through the clogged sewage pipe and can thus solve the blockage. Persistent blockages can be removed with a connected drill or hook.

It is not uncommon for private individuals to apply such a spiral. Here, the problem often arises that the introduced spiral cannot be pulled out — the pipe cleaning spiral is then removed with great effort, again damage to the pipe can occur.

Furthermore, thermal cleaning is possible in which the interior of the tubes is dried. As a result, the blockages dry out and can fall off.

However, this procedure is usually only carried out with impurities — in addition, the wastewater plant would have to be switched off for this purpose.

In most cases, therefore, the mechanical cleaning is preferred, but the sanitary technician usually decides which method is best on site.

How to prevent clogged drains

It is always an unwelcome and unpleasant experience when one of your drains secures and leaves you with a mess.

There are many products on the market designed to correct congested drains, but it would be ideal to completely avoid the problem.

Not many people think ahead to prevent clogged drains — but there are several ways in which you can keep water running through your pipes smooth.

Pour into tins used cooking fat. Fat is very harmful to your pipes because it settles on their sides and acts as a trap for discarded food bits. Over time, the accumulation of particles that drain-clog.

Boil some water to keep the pipes clear. Either weekly or monthly, boil a kettle of water and pour it down each sink in your house.  

Clean strokes regularly. Once a week, remove all sink stoppers and pop-up stoppers and wash and rinse them thoroughly. Stoppers are first-class places for loose hair to get stuck and clog the drain.

Make it a habit to flush only “flushable” products into the toilet. Never flush large or heavy paper products in the toilet.

Installing strainers over the kitchen and bathroom drains hair, soap, and food residues — thus preventing them from getting into the pipes and clog, and thereby clogging the drains. Just be sure to keep the strainers clean.

If you notice your processes are running slowly, it’s time to take action. Remove the piston or/and the assembly before it becomes more of a problem.

What are the symptoms of a full septic tank?

When you flush your toilet, the wastewater flows into the septic tank where it settles. Solid waste settles at the bottom of the septic tank, while aqueous liquid is absorbed from the tank through small discharge pipes and near fields.

Septic tanks require little maintenance and must be pumped every three to five years. When your septic tank fills up, the drain pipe can become clogged, in tank failure.

1. Your toilets back up

One of the most important symptoms of a complete septic tank is slow toilet drainage or constipation.

Your normally well-functioning toilet may start to secure spilling sewage into your home, or it may require several flushes to drain completely.

This can encourage germs to breed and cause a serious health issues for both you and your family members.

According to Australian Government Department of Health, Hepatitis A, Trachoma, Diarrhoea, and Shigellosis are some of the prevalent bacterial and viral diseases people experience of poor toilet hygiene and sewage that is not properly disposed.

2. A wetland appears above the septic tank

If your septic tank is working properly, the area above and around the tank will be dry. If a wet, muddy area appears above the tank; your septic system may be full and overfilled into your garden. You can see sewage or even toilet paper in extreme overflowing cases in your garden.

3. It’s been more than five years since the last pumping

You should have your septic tank pumped every three to five years to avoid the tank from clogging or overfilling. If it has been more than five years since the tank was last cleaned, your septic tank is full.

3. Your septic tank smells

Normal, well-functioning septic tanks are odorless. If you notice a foul smell decomposing outside around your septic tank or in your bathroom, this can be a sign.

The smell can be persistent or can only occur in hot weather.

Here’s an illustration that shows how a Septic Tank works

Source: Amazon

Conclusion

Sewage backup can occur when different materials accumulate in sewer pipes. Grease, hair, dirt or other solid material can build up and eventually clog sewage pipes.

By following the proven tips in this article, you’re on your way to achieving a clog-free sewer drain and enjoying a healthy lifestyle.

Google+

Pinterest

Linkedin

Twitter

Facebook

Reddit

An obstructed drain is always a problem and can seem complicated if you do not know what to do. A study by Direct Energy revealed that clogged toilets and Kitchen sink drain results when dirt, skin flakes, hair binds, cooking grease trapped onto drain pipe walls, and several other elements can pose a difficult problem in the home.

Fixing clogged drains isn’t going to be fun, it’ll smell bad, and you should be ready for the mess.

The good news is: We’ve put together proven tips to help you learn how to unclog a drain and get your plumbing and drainage system functioning properly.

In this informative article, you will how to:

• Identify a clogged drain.
• Clean a clogged drain.
• Avoid future blockages.
• Understand your responsibility for unblocking public and private lines.

So what basic steps do you need to take if you experience a clogged drain? This is one of the major concerns that homeowners have. Let’s discuss it.

1). Identify what is wrong

If the water in your toilet or bathroom does not drain away properly, it is likely to be the result of a clogged drain. If your toilet is completely clogged, check out our article on how to unclog a toilet.

2). Stop using the drain

This may seem obvious, but do not throw more water down the drain! This will only make the problem more difficult to solve.

3). Safety first

Before tackling the blockage, make sure you stay safe by wearing full protective clothing (including gloves, goggles, and coveralls). And always remember to remove and wash your protective clothing after completing the work.

That said, let’s now talk about the best ways to handle a clogged drain.

Before you begin, make sure you have a set of pipe rods, which can be rented or purchased at most DIY stores. Once you have put on your protective clothing, follow the steps below.

1. Remove the lid

First, lift the inspection cover over the drain. If the lid is rusted off, use a screwdriver to scrape off the rust. If your manhole has a handle, attach a string or wire to it, then open the lid.

2. Unclog

Use a rod with a piston attachment to dislodge the obstruction — it can take several minutes of twisting and turning. If not, try using a standard kitchen mop handle even though this is unlikely to be as versatile as a goal drain rod does.

On the flip side, you can use the plunger. A report by Consumer Reports shows that you can use biological cleaners and a plunger to clear under sink clogs.

“The report further revealed that Biological cleaners, such as Citra-Drain and Zep, use enzymes or bacteria to chew through clogs. It doesn’t pose a health risk to humans, and they’re likely to harm septic systems because they don’t kill beneficial bacteria. But they’re very effective when it comes to quickly removing clogs.”

3. Rinse with water

Once you have dislodged the blockage, flush the drain with water to remove the remaining debris. Unlocking a drain can be a difficult process that is best avoided.

Here are some tips to prevent future drainages:

• Watch your drains: By checking your drains regularly; you should be able to take the start of all minor blockages before they get worse.
• Dispose of waste properly: Remember to dispose of waste in the correct manner. Never rinse items such as face wipes, diapers or cotton wool as they may block drains.
• Keep your drains clear of plants: If possible, try to keep clear drains of flowers and plants. If your garden is particularly green — try the drain fitting guards to help prevent plant material from falling in and causing blockages.
• Rinse before loading your dishwasher: Always rinse plates and cutlery before loading your dishwasher. Any excess food will end up in the drains and could build up to cause a blockage.

Find out your responsibilities as the homeowner or occupant and the person to contact if you are having a problem with a public drain or sewer.

Method of Unblocking pipes:

i). Unblocking by pump: Recommended for small plugs, its efficiency is proportional to the strength of the user.

ii). Unlocking by ferret: For small and medium plugs, the ferret goes everywhere in the pipe and allows to eliminate the plug.

iii). Unclogging by acid: For small and medium caps, acid does wonders. In less than a quarter of an hour, the acid will completely dissolve the cork. The only disadvantage is that the pipeline can be thinned.

iv). Unloading by truck pump: Recommended for large caps, it is a hydro-pump truck that sends a jet of water at high pressure in the pipes. Its action is extremely effective and performs a thorough disgorging and scrubbing of the pipeline.

The importance of the cap depends on the diameter of the pipe and the nature of the plug itself (hair, food scraps, toilet paper …).

Pro Tip: Avoid throwing anything into your pipes and maintain them regularly.

Flushing

Flushing is a effective method of cleaning a clogged drain. Flushing helps to unstop a slow running sink and you don’t have to use toxic chemicals or even seeking the help of a plumber.

However, if the task is beyond you, you might want to get some help from a qualified plumbing company near you.

The right plumbing company doesn’t do this for money. In fact, most of the work they do is to carry out the maintenance of sanitation networks for the direct needs of communities, municipalities, companies, and individuals in order to ensure the durability and the flow of the works, but also to avoid odors.

The ideal plumbing company will also ensure the cleaning of the wastewater columns, garbage disposal ducts, building rubbish bins on behalf of Condominium Trustees, maintenance of lifting pumps, cleaning of lagoons and rhizospheres.

Principle and operation of pipe cleaning

The cleaning head is the working tool for the implementation of pressurized water, especially for the cleaning, stripping, and cleaning of pipes.

The cleaning head performs a dual function:

i). The projection of water under pressure: The front jets prepare and facilitate cleaning work in the case of heavily clogged pipes.

ii). Propulsion: The rearward directed jets are dimensioned according to the flow/pressure torque and oriented according to the desired speed of travel and the work to be done.

So how do you know there’s a problem with your plumbing system?

You know that you have a problem with your plumbing system when some clues appear, such as:

• Weird noises.
• Unpleasant odors.
• slow and difficult evacuation.

And so on.

The situation can become frustrating and even detrimental to your quality of life.

And it doesn’t make sense to just sit back and watch the situation change on its own accord. No, you have to take the right steps and contact a plumber who can fix it quickly and safely.

Why use the services of a plumber?

If you are not a plumbing specialist, you may only perceive the symptoms of the problem. But it doesn’t stop there. How would you know if it is due to:

• A clogged drain.
• A leaking pipe.
• Dysfunctional sewers.

Etc.

Remember that damaged piping can cause more leaks and damage to your house. Hence, the need to seek professional support.

More so, the congestion of a pipe may be a symptom of an underlying problem that needs to be addressed without delay.

A plumbing professional will be able to intervene:

• Quickly.
• Properly.
• With the right equipment.

How do you know the right specialist to call?

If you are unsure about the professional who can help you, contact us by phone or online to get the information you need. You will know if the plumber is the specialist who can suit your situation or if you should rather call a general contractor, an electrician, a carpenter, etc.

What can a plumber do when the plumbing problem touches the foundation drain?

There are two (2) types of problems that can occur with foundation drains (also known as French drain):

• The pipes are blocked by the roots of the trees.
• They are engorged by iron ocher.

How can a plumber perform hose uprooting?

How can an outside pipe be blocked by roots? It is known that plant roots seek water. That’s one of the reasons the roots grow in that direction. It is enough that your external pipes:

• Show signs of condensation on the outer walls.
• Slightly ooze or
• That the seals are loose and cause water to leak.

When they reach the pipes, the roots are inserted through the cracks (even in the most microscopic ones), develop and grow until they completely block the pipe or cause it to break. If you have waited too long, you will have no choice but to replace them entirely.

How to locate where the foundation drain is obstructed?

If in the past you had to dig at random, which increased the costs of the intervention today, it is possible to do a complete inspection of your pipes with a specially designed camera.

There is more than one type of camera for this purpose. However, keep these things in mind when choosing a camera:

• Color or black and white images;
• Length of the semi-flexible stem of the file to which it is connected;
• Resolution of the image;
• Dimension of the camera;

If your pipes do not have openings for their maintenance, a trench will be dug on a corner of the building, the foundation drain will be cut and a camera will be inserted into each section to make a complete tour of the damaged drain (if no cluster blocks the passage of the camera).

But the camera also has many other uses:

i). Detect other alterations such as, for example, a major breach affecting a wall of the foundation;

ii). The ownership and distribution of sand and crushed material preventing water (rain or groundwater) from remaining near and infiltrating the foundations.

iii). Find out if the foundation drain(or French drain):

• Has aged badly;
• Is holed
• Contains earth;
• Is clogged with ferrous ocher;

If on its way, the camera detects a flow or other important problems, then you’ve no choice other than to excavate the area and fix it.

How can plumbers uproot the foundation drain?

If the process is not too advanced, the extraction of the roots can be done with the help of an electrical feeder. This ferret is made up of a thin, elongated, semi-flexible metal part with blades that can cut the roots, clean or reduce to pieces any clog that clogs the French drain.

Do solutions exist to the problem of pipes clogged with ferrous ocher?

Research is still underway to discover how to permanently eliminate iron ocher problems. The best solution, for the moment, is maintaining your pipeline.

The first time, the work will be a little more expensive.

Remember that you can request a quote from a plumber. Indeed, it will be necessary to dig, cut a section of the French drain, circulating a jet of pressurized water in the latter for effective cleaning, bleach to lower the pH in the event that the iron ocher deposit is of bacterial origin, check again to make sure there are no more ferrous ocher plugs, put ducts (chimneys) in place so you do not have to dig and cut again at the next maintenance.

Once the ducts (chimneys) are installed, the cost of a “foundation drain cleaning” should cost only one-quarter (¼) of the initial amount depending on which plumbing company you have chosen when you receive quotes from Plumber.

Other solutions:

• Copper wire in the drains so that the iron deposits settle there. The role of this copper wire is somewhat the same as that of the anticorrosive anode in a water heater.
• Drains covered with water.
• Materials with large filtration openings to benefit the ocher composition away from the drains.
• The addition of lime to the backfill soil (when the soil is fine textured).
• Smaller distance between large diameter pipes.
• Lateral drains shorter.

9 tips for maintaining your plumbing system

1. Take advantage of the services of a plumber expert

The first advice we can give you to keep a plumbing system in perfect condition and save money may seem to be interested on our part but it is the most efficient and the least expensive: Call a plumber expert at the first sign of a failure of your system. You will avoid serious problems and disbursements.

2. Avoid carelessness and prevent obvious issues

The majority of plumbing and water damage we face is due to negligence. Many of your plumbing problems and significant costs can be prevented.

Keep a regular eye on the failures of the components of your plumbing system. Inspect countertops by opening cabinets under your kitchen sink and bathroom sink for leakage or moisture.

Stretch your ear to check for any noise from your toilet tank to make sure there is no spillage as well as any seepage from its connection.

Inspect the flexible hoses connecting your clothes washer, especially if they are a few years old. Being able to inspect the connections and the underside of your dishwasher for leaks is an asset.

Inspect your water heater for leakage or rust and make sure you know where it is going. When the water supply piping is visible, inspect it.

Also, inspect walls and ceilings under plumbing fixtures and components for dark circles or moisture when possible. Also, make sure your drains are working properly.

This inspection will only take a few minutes but will ensure that your plumbing system is kept in good condition and at a lower cost.

3. Prevent the bursting of pipes by frost

If you have water pipes, both metal and PVC that run along an outside wall and are visible to you, inspect them in very cold weather.

If you leave your home for a long time in the winter or during a prolonged heating failure, take advantage of these few recommendations:

• Beware of lowering the heating of your home
• Leave your cabinet doors under your sink or sink to keep enough temperature in these confined spaces
• Let a trickle of water run down your faucets to prevent freezing of stagnant water in your piping

Also make sure your piping and fittings are well insulated in the unheated areas of your home and garage.

If you are closing your cottage for the winter, be sure to close the main water inlet and let the faucets run to completely empty your pipes. Remember to make sure your water supply is well insulated upstream of your main water inlet valve.

4. Check your water heater

Check for leaks and rust. From 10 years of age, you must seriously think about replacing it. You avoid major damage that will cost you thousands of dollars, especially if you live in a housing or condo.

5. Your washing machine or dishwasher hoses

Regularly check your washing machine and dishwasher hoses. The rubberized casings of your clothes washer dry out with age and show signs of weakness through external cracks.

You must change these guts at the first sign of weakness or every 10 years. The same goes for your dishwasher hoses, even if they are flexible metal.

Always choose quality materials, save a few dollars at the risk of causing damage for several thousand dollars is not a good economy.

6. Your outdoor faucets

Remember to empty your outdoor water supply ducts before winter, whether for your pool or garden hose, unless you have frost-free faucets. If you have an unheated garage that is supplied with water, consider also protecting yourself from frost.

7. Act quickly in case of emergency

Even if you take all the necessary care to avoid a leak or a water damage, a breakage can happen. Immediately close the supply valve of the defective plumbing element.

This valve is usually located close to the item to repair for example, under your sink or sink, behind your clothes washer, a hatch behind your bath supply or, above your water heater.

If you cannot stop the leak, turn off the main power of your home immediately. It is usually in the basement near the wall facing the street and the municipal power system.

8. Thaw frozen pipes

According to Reader’s Digest, “frozen water expands in volume by up to 9%. And this expansion is spontaneous: going from 40 pounds per square inch to 40,000 pounds per square inch.”

More so, when you run out of water or have a very low water pressure in the winter on a particular component of your plumbing system and its pipe runs near an outside wall exposed to the cold, you probably have a problem with a frozen pipe. It is necessary to act quickly before undergoing a burst.

You need to identify where the frost is forming, usually in a closet or cabinet leaning against an outside wall when the plumbing is visible. These are cooler places that can be poorly insulated.

To help resume normal flow, open the valve on the section affected by the freeze. The most effective and safest way and the use of a hairdryer.

You must distribute the heat evenly up to the frozen part of the piping and be patient. Other heating elements such as a heating fan, or an electric lamp that emits a lot of heat can be used.

But be careful not to ignite flammable components surrounding your piping. The propane torch is to be avoided. The danger of fire is too great and you can damage your piping.

When the pipe is not visible, you must use the same means to warm the environment of your hidden piping. But you will have to redouble your patience.

If you are unable to restore water flow, call a plumber quickly to avoid having an exploded pipe and subsequent water damage.

To prevent pipes from freezing in the most at-risk locations, you can wrap your pipes with insulating foam covers that are available at low-cost hardware. Heating wire may be required in less accessible areas.

9. Prevent clogged pipes with a house cleaner

Make your own sewer pipe cleaner with homemade products at your fingertips. Pour equal parts of baking soda and vinegar into your tub or sink drain once a month.

Conclusion

You can also use two products that you usually find in your kitchen to prevent clogged pipes. Use half a cup of baking soda and half a cup of salt to mix and empty into your drain. Add boiling water.

These two methods are all as effective and less harmful than the products available on the market while being more natural and less toxic.

Other so-called eco-friendly enzyme products are coming onto the market and can help keep your ducts clean. These enzymes digest the accumulated dirt in your ducts but do not open an already clogged pipe.

In addition, experts do not unanimously agree on the real impact of these products on the ecology.

Google+

Pinterest

Linkedin

Twitter

Facebook

Reddit